AFUE – Annual Fuel Utilization Efficiency, a rating that reflects the efficiency of a gas furnace in converting fuel to energy. A rating of 90 means that approximately 90 percent of the fuel is utilized to provide warmth to your home, while the remaining 10 percent escapes as exhaust.
Allegiance® – The best air conditioner available today. Available only from American Standard.
Bels – Units of sound measurement. Each .3 increase in bels doubles the sound power output.
Boiler – Apparatus for heating water for use in various domestic and commercial applications.
BTU – British Thermal Unit. In scientific terms, it represents the amount of energy required to raise one pound of water one degree Fahrenheit. One BTU is the equivalent of the heat given off by a single wooden kitchen match. For your home, it represents the measure of heat given off when fuel is burned for heating or the measure of heat extracted from your home for cooling.
CFM – Cubic feet per minute, a standard of airflow measurement. A typical system produces 400 CFM per ton of air conditioning.
Capacity – The output or producing capability of a piece of cooling or heating equipment. Cooling and heating capacity are normally referred to in BTUs.
Coastal Coating – Special coating applied to HVAC coils to guard against coastal salt corrosion.
Compressor – The heart of an air conditioning or heat pump system. It is part of the outdoor unit that pumps refrigerant. The compressor maintains adequate pressure to cause refrigerant to flow in sufficient quantities in order to meet the cooling requirements of the system.
Condenser Coil or Outdoor Coil – Located in the outdoor unit, the coil dissipates heat from the refrigerant, changing the refrigerant from vapor to liquid. In American Standard units, the coil is called Spine Fin.
Damper – Found in ductwork, this movable plate opens and closes to control airflow. Dampers are used effectively in zoning to regulate airflow to certain rooms.
Duration – American Standard’s tough, time-tested compressor. Also referred to as Climatuff.
Downflow Furnace – A furnace that pulls in return air from the top and expels warm air at the bottom.
Ductwork – Pipes or channels that carry air throughout your home.
Evaporator Coil – The coil that is inside your house in a split system. In the evaporator, refrigerant evaporates and absorbs heat from air passed over the coil.
FAU – Forced Air Unit. Commonly used to refer to a furnace.
Freedom® – The best gas furnace available today. Available only from American Standard.
Heat Exchanger – A device for the transfer of heat energy from the source to the conveying medium.
HEPA – High Efficiency Particulate Arrestor – Specially designed air filtration that can stop pollen and dustmites.
Heritage® – The best heat pump available today. Available only from American Standard.
Horizontal Furnace – A furnace that lies on its side, pulling in return air from one side and expelling warm air from the other.
Humidifier – A device that injects water vapor into heated air as the air is expelled from the furnace.
Humidity – The amount of moisture in the air. Air conditioners remove moisture for added comfort.
HSPF – Heating Seasonal Performance Factor – Refers to the efficiency of the heating mode of heat pumps over an entire heating season. The higher the number, the more efficient the unit.
HVAC – Heating, ventilation and air conditioning.
ICM – Integrally Controlled Motor – A specially engineered, variable-speed blower motor that provides quiet operation and 90% system efficiency, versus 60% for conventional PSC blower motors.
LEED: Leadership in Energy and Environmental Design – Rating system for Green building design.
Packaged System – A piece of air conditioning and heating equipment in which all components are located in one cabinet. Used occasionally in residential applications, the packaged unit is installed either beside or on top of the home.
Refrigerant – Substance that produces a refrigerating effect while expanding or vaporizing. Commonly called Freon.
Refrigerant Lines – Set of two copper lines connecting the outdoor unit and the indoor unit.
SEER – Seasonal Energy Efficiency Ratio – A rating that measures the cooling efficiency of a heat pump or air conditioner. The higher the number, the more efficient the unit.
SEET – Seasonal Extreme Environmental Test – American Standard’s torture chamber for equipment testing, where five years of operation are condensed into 16 torturous weeks.
Spine Fin – Constructed of thousands of tiny spines bonded to continuous aluminum refrigerant tubing, this revolutionary, patented coil is used in Allegiance and Heritage products. Because of its greater surface area, Spine Fin has greater heat transfer capabilities – it’s also unbeatable in providing retained efficiency over time.
Split System – Refers to a comfort system configuration consisting of components in two locations. Common examples include an outside unit, such as an air conditioner, and an indoor unit, such as a furnace and coil.
Switchover Valve – A device in a heat pump that reverses the flow of refrigerant as the system is switched from cooling to heating. Also called a reversing valve or four-way valve.
Thermostat – A temperature control device, typically found on a wall inside the home. It consists of a series of sensors and relays that monitor and control the functions of a heating and cooling system. American Standard’s programmable thermostats allow you to program different levels of comfort for different times of the day.
Ton – Unit of measurement used for determining cooling capacity. One ton is the equivalent of 12,000 BTUs per hour.
Upflow Furnace – A furnace that pulls return air in from the bottom and expels warm air from the top.
Zoning – A method of dividing a home into zones for controlling the amount of air provided to each.